Pneumatic membrane PTFE single seat control valve is controlled instrument in the execution unit. It consists of pneumatic diaphragm actuator and direct single seat of fluorine plastic valve of two parts. Since the valve wetted parts are high-pressure injection molding process, lining has the capability to corrosion and aging of FEP (F46), and the use of PTFE bellows seal, so that the valve is widely used in chemical, petroleum, metallurgy, medicine, power and other industries in the process of acid and alkali corrosion medium and toxic and volatile gas and liquid medium control.
Valve body, valve cover:HT200,ZG230-450,ZG1Cr18Ni9Ti
Valve core and valve seat:1Cr18Ni9Ti,Welding division Stellite alloys
Soft sealing valve core: Reinforced PTFE
Corrugated pipe: 1Cr18Ni9Ti PTFE bellows
Filling piece: Rubber asbestos board, 10'', 1Cr18Ni9Ti asbestos gasket
Membrane cover: A3
Corrugated diaphragm: butyl rubber clip reinforced polyester fabric
Spring:30SIMN
Stem, push rod:2Cr13、1Cr18Ni9Ti
bushing:2Cr13
project
|
performance index
|
Basic error%
|
≤±8
|
Return difference%
|
≤8
|
dead zone%
|
≤6
|
Rated flow coefficient error
|
≤±10%(Kv≤5時(shí)±15%)
|
Leakage rate
|
≤0.01%Rated capacity of valve
|
Nominal diameter DN(mm)
|
G3/4''
|
20
|
25
|
32
|
40
|
50
|
65
|
80
|
100
|
150
|
Valve seat diameter DN(mm)
|
3
|
4
|
5
|
6
|
7
|
8
|
10
|
12
|
15
|
20
|
26
|
32
|
40
|
50
|
65
|
80
|
100
|
150
|
Rated flow coefficient KV
|
0.08
|
1.12
|
0.20
|
.032
|
0.50
|
0.80
|
1.2
|
2
|
3.2
|
5
|
8
|
12
|
20
|
32
|
50
|
70
|
100
|
240
|
Flow characteristics
|
straight line
|
Linear, equal percentage
|
Nominal pressure PN(Mpa)
|
1.01.6
|
With the actuator
|
Model
|
ZHA-22
|
ZHA-23
|
ZHA-34
|
ZHA-45
|
|
effective area cm
|
200
|
280
|
400
|
630
|
1000
|
|
Working stroke mm
|
10
|
10
|
16
|
25
|
40
|
60
|
|
Spring range KPa
|
20-10040-200
|
Mode of action
|
Air or gas
|
working temperature
|
-30~200℃
|
Inherently adjustable ratio R
|
30:1
|
Nominal diameter DN(㎜)
|
3/4″
|
20
|
25
|
32
|
40
|
50
|
65
|
80
|
100
|
150
|
L
|
116
|
180
|
185
|
200
|
220
|
250
|
275
|
300
|
350
|
480
|
A
|
245
|
245
|
245
|
245
|
290
|
290
|
362
|
362
|
362
|
454
|
H
|
401
|
445
|
485
|
495
|
523
|
532
|
697
|
699
|
699
|
817
|
H1
|
50
|
65
|
70
|
80
|
71
|
88
|
102
|
140
|
170
|
190
|
weight
|
17
|
17
|
19
|
21
|
28
|
31.5
|
54
|
64
|
80
|
120
|
The standard group with the single seat pneumatic valve, the output force of the pneumatic diaphragm actuator is certain. In order to achieve the ideal adjustment and closing, the pressure of the valve must be limited to a certain value, the product should be selected according to table 3. When the pressure exceeds the allowable value, adjustable spring preload, equipped with a valve positioner or use other actuators to overcome the imbalance of power, but the order must contact with my company, explaining the situation before ordering.
Gas supply pressure(MPa)
|
Spring range(MPa)
|
Nominal diameter(DN)
|
G3/4''
|
20
|
25
|
32
|
40
|
50
|
65
|
80
|
100
|
150
|
Valve seat diameter(DN
|
3-8
|
10
|
12
|
15
|
20
|
26
|
32
|
40
|
50
|
65
|
80
|
100
|
150
|
0.14
|
20~100
|
Allowable differential pressure△P(MPa)
|
1.6
|
0.8
|
0.5
|
0.5
|
0.3
|
0.25
|
0.2
|
0.12
|
0.08
|
0.24
|
40~200
|
|
-
|
1.2
|
1.1
|
0.7
|
0.65
|
0.45
|
0.28
|
0.20
|